Kidde AirSense Stratos HSSD 2 is designed to provide very high-sensitivity smoke detection, ensuring the earliest possible warning of a developing fire while minimising nuisance alarms.
ClassiFire Perceptive Artificial Intelligence ensures the detector operates at optimal sensitivity for the protected environment, without the need for a complex setup. This means the product will configure itself to provide high sensitivity in a computer room or reduced sensitivity in a smoky area.
Upgradable volt-free Fire and Fault relay outputs are available for remote monitoring by local fire detection or BMS systems.
Details
- High sensitivity provided by laser-based forward light scatter for reliable early warning.
- Four sampling pipes, combined sampling pipe up to 200m in length (still air), overall diameter 27mm.
- Laser Dust Discrimination (LDDTM) makes this product suitable for a wide range of environments.
- Unique ClassiFire Perceptive Artificial Intelligence system that dynamically adjusts the detector’s operating parameters, allowing for day-to-day changes in the protected environment and dust separation system contamination.
- Unwanted dust alarms are avoided with the patented Dual Technology LDD 3D3 Laser Dust Discrimination and Elimination system.
- RS-485 communications are built in as standard for networking and remote communications.
- Approvals: CPR, LPCB, VdS, NF, CSIRO, UL & FM.
Typical Applications
- Data storage units
- Prison cells
- Plant rooms
- Air conditioning units
- Equipment racks
- Computer rooms
- Air duct protection
- Heritage property protection
- Critical equipment
- Anti-smoking enforcement
- Motor rooms
Options Available
- Addressable Protocol Interface Cards APIC) are available for the Ziton protocol.
- Command Module available for central monitoring and display.
- SenseNet compatible – up to 127 detectors per loop.
- Remote Display units available.
- Suitable for MatrixScan, a patented software system which provides virtual addressable location detection – e.g. 10 physical detectors would provide up to 45 unique addressable locations.
Part of the ASD range by UTC Fire & Security, also branded under the Air Intelligence name.
Order Information
| 9-30621 | Stratos HSSD 2 Four-pipe single-detection-zone aspirating smoke detector. LCD and LED status indicators; the unit is fully programmable via the front membrane; four-alarm levels with relay outputs; 3 x programmable inputs. SenseNET network ready. Requires an external 24VDC supply. Maximum pipe length: 4 x 50m no. of Sample holes: Class A – 20, Class B – 40, Class C – 100 Sampling holes Dimensions mm: 427w x 372h x 95d |
| 9-30620 | Stratos HSSD 2 with Command Module As per part number 30621, with command module functionality included. The command module functionality provides central control for all detectors connected on a network. Large LCD provides detailed status information. Requires an external 24VDC supply. Maximum pipe length: 4 x 50m no. of Sample holes: Class A – 20, Class B – 40, Class C – 100 Sampling holes Dimensions mm: 425w x 370h x 115d |
| 9-30706 | Stratos HSSD 2 – Steel enclosure As per part number 30621, it has a steel front cover for industrial-type applications. Requires an external 24VDC supply. Maximum pipe length: 4 x 50m no. of Sample holes: Class A – 20, Class B – 40, Class C – 100 Sampling holes Dimensions mm: 425w x 370h x 115d |
| 9-30707 | Stratos HSSD 2 with Command Module – Steel enclosure As per part number 30620, it has a steel front cover for industrial-type applications. Requires an external 24VDC supply. Maximum pipe length: 4 x 50m no. of Sample holes: Class A – 20, Class B – 40, Class C – 100 Sampling holes Dimensions mm: 425w x 370h x 115d |
| 9-30710 | Stratos HSSD 2 Minimum display As per part number 30706, with basic LED status indications for Fire, Fault and OK. Requires an external 24VDC supply. Maximum pipe length: 4 x 50m no. of Sample holes: Class A – 20, Class B – 40, Class C – 100 Sampling holes Dimensions mm: 425w x 370h x 115d |
| Modules | |
| 9-30624 | Stratos Command Module Provides a single location for display, control, and interfacing for networks of up to 127 detectors. The Command module allows global programming of all detector functions simultaneously. Large LCD and LED status indications. Requires an external 24VDC supply. Dimensions mm: 425w x 370h x 115d |
| 9-30709 | Stratos Command Module – steel enclosure As per part number 30624-KID, it has a steel front cover for industrial-type applications. Requires an external 24VDC supply. Maximum pipe length: 4 x 50m Dimensions mm: 425w x 370h x 115d |
| Accessories | |
| 9-30841 | EN 54-4 approved, 24 V 2 A + 0.8 A Intelligent Power Supply A versatile solution for powering aspirating smoke detectors. A high-capacity power supply provides current for ‘day-to-day’ system operation while charging backup batteries. The PSU can provide 24-hour mains-fail battery backup using industry-standard sealed lead-acid batteries. A relay output is provided for remote monitoring of mains fails and battery faults. Dimensions mm: 400w x 420h x 80d Contains space for 2 x 17Ah batteries max Please note: 12Ah batteries will not fit inside this power supply |
| 9-30842 | EN 54-4 approved, 24 V 5 A + 1.6 A Intelligent Power Supply A versatile solution for powering aspirating smoke detectors. A high-capacity power supply provides current for ‘day-to-day’ system operation while charging backup batteries. The PSU can provide 24-hour mains-fail battery backup using industry-standard sealed lead-acid batteries. A relay output is provided for remote monitoring of mains fails and battery faults. Dimensions mm: 400w x 420h x 80d Contains space for 2 x 17Ah batteries max 2 x 38Ah batteries can be connected using the remote battery box part number 30843 Please note: 12Ah batteries will not fit inside this power supply |
| 9-30843 | External battery box For use with power supply part number 30842. The remote battery box allows connecting 2 x 38 Ah batteries to the power supply. Dimensions mm: 420w x 420h x 280d |
| 9-30802 | Stratos Remote Display Unit (RDU) The RDU connects to the Stratos range of detectors via the RS-485 data bus and mimics the detector’s LED status indications. The RDU monitors the status of a single detector. More than one RDU can be allocated to a single detector. The RDU can be mounted in either a single wall-mounted enclosure or a 3U high 19″ rack enclosure. Requires a 24VDC supply. |
| 9-30803 | RDU Relay board This is an optional relay board that can be used with the Stratos RDU to provide Volt-Free Changeover Contacts for signalling to other equipment. Five relays are provided for Fire 1, Fire 2, Pre-alarm, Aux Alarm and Fault (energised). |
| 9-30436 | Relay/Input card The Relay/Input card can be fitted into the Micra 10, Micra 25 and 100 detectors to provide an additional five relay outputs for signalling to other equipment. Three inputs are provided on the card that can be programmed for remote reset, isolate, classifire override or PSU fault monitoring. |
| 9-30430 | APIC card – Apollo protocol An addressable interface card is fitted internally to any Stratos detector unit or Command Module, allowing them to be connected to an Apollo protocol addressable loop. A single APIC may be used in Multi Address mode when installed inside a command module to signal up to 127 detectors onto the addressable loop, reducing costs in larger systems. |
| 9-30438 | APIC card – Hochiki protocol As part number 30430 for Hochiki protocol panels |
| 9-30433 | APIC card – Notifier protocol As part number 30430 for Notifier protocol panels |
| ZP-LSI-1 | APIC card – Ziton protocol As part number 9-30430 for Ziton ZP2 and ZP3 protocol panels |
| 9-30419 | Stratos Serial cable Required for connecting a laptop or PC to a Stratos Aspirating Smoke Detector. Allows Stratos Remote software to communicate with the detection unit, enabling programming and diagnostic facilities. The cable is a 9-pin-to-9-pin female D-type null modem crossover. |
| 9-30817 | Single Remote Display Unit wall mounting enclosure Small steel enclosure for wall mounting a single Remote Display Unit (30802) and optional relay board (30803). |
| 9-30814 | RDU 19″ subframe 19″ chassis can be used to mount multiple Remote Display Units inside a 19″ rack cabinet. The chassis is 3U high and can accommodate 7 RDUs |
| 9-30812 | RDU blank fill plate Used in conjunction with 9-30814 subframe when not installing the full compliment of RDUs the blank plate will cover any unused slots. |
| 1-21888-K063 | PSX3 Particle Separator The particle separator is used to limit contamination of the detector when installed in dirty, dusty environments. The unit is supplied with union sockets to allow it to be used with 25mm and ¾” pipework. Foam elements inside the unit can easily be replaced as necessary. The unit is supplied with union sockets to allow it to be used with 25mm and ¾” pipework. Foam elements in the unit can be easily replaced as needed. Replacement foam elements, part number 21888-K064-P. Enclosure Dimensions mm: 160h x 160w x 90d |
| 9-30730 | Stainless steel external filter Commonly used with the Stratos Ex unit, the filter controls the dust and dirt contamination in harsh environments. As the unit is external to the detector enclosure, access to the filters for maintenance is easier and in hazardous areas prevents the need to declassify the area. 304 Grade stainless steel enclosure, requires 2 x filters (30072) |
| 9-30422 | Air Heater box Suitable for installations where humidity or condensation may be a problem. The air heater heats and dries the air before it reaches the detector, removing any moisture and preventing condensation from cold air entering the detector. Enclosure Sheet Steel, Heating element Self-regulating 230 VAC, 60/200 watts. It is recommended to fit a thermostat to the heater box to control the temperature. Kidde does not supply a thermostat. |
| BS131N | Battery 12V 18 AH Sealed lead-acid battery Output voltage: 12VDC Max charge voltage @ 20oC: 13.8VDC, Max charge current: 5.4A Dimensions mm: 181h x 76w x 167d |
| Software | |
| 9-30250 | SenseNET Software with a license dongle A software package which allows networks of Stratos detectors to be monitored centrally from a PC. Graphical maps of the site can be imported to easily locate detectors, alarm zones, etc. Up to 16 individual networks can be monitored. |
| Spare Parts | |
| 9-30698 | Stratos HSSD 2 detector head assembly Replacement detector head for all variants of the Stratos HSSD 2 Aspirating Smoke Detector. |
| 9-30697 | Stratos HSSD 2 Main PCB Replacement main PCB for all variants of the Stratos HSSD 2 Aspirating Smoke Detector. |
| 9-30696 | Stratos HSSD 2 display Replacement display module for all variants of the Stratos HSSD 2 Aspirating Smoke Detector, excluding models 30620 and 30707, which require the command module display 30691 |
| 9-30695 | Stratos HSSD 2 flow sensor PCB Replacement flow sensor PCB for all variants of the Stratos HSSD 2 Aspirating Smoke Detector. |
| 9-30058 | Stratos HSSD 2 Replacement fan assembly Replacement fan assembly for all variants of the Stratos HSSD 2 Aspirating Smoke Detector. |
| Filters | |
| 9-30699N | Individual HSSD2/ModuLaser A single cartridge-type filter for use with all variants of the Stratos HSSD2 or ModuLaser Aspirating Smoke Detection units. One filter required per unit. |
| 9-30699N-P | HSSD2/ModuLaser filter pack A pack of 6 cartridge-type filters for use with all variants of the Stratos HSSD2 or ModuLaser Aspirating Smoke Detection units. One filter required per unit. |
| 9-30072-P | HSSD MK1 & Ex filter pack A pack of 6 cartridge-type filters for use with all variants of the Stratos HSSD MK1 Aspirating Smoke Detection unit. NB: Stratos HSSD MK1 is an obsolete product, and it is advised to upgrade these detectors as soon as possible. This filter is also used inside the external stainless steel filter unit (30730). |
| 1-21888-K064-P | Particle separator filter pack A 6 Pack of replacement filters for the particle separator 21888-K063 Each replacement filter pack contains 3 x foam elements; one pack is required per particle separator. |
