|
ALARMLINE II INSTALLATION ACCESSORIES |
|
Alarmline Specialist Application Accessories |
| 1-B6782-032 |
Cable collector, stainless steel
Designed to be fixed to the roof of a floating roof storage tank for collecting the retractable cable (B6782-032). The cable collector rises and falls with the movement of the roof, uncoiling the cable when the roof lowers and collecting the cable when the roof rises. The collector is supplied with drainage holes.
Material: Stainless Steel 304
Dimensions: diameter 624mm, height 505mm |
| 1-B6782-170 |
Retractable cable – 30m
Used in conjunction with the cable collector (B6782-032) retractable cables are designed to provide electrical connection from tank roof to tank top on floating roof tanks, reducing the risk of cable being caught and snapped during the normal rising and falling movement of the tank roof.
The cable contains four cores with an overall diameter of 10mm |
| 1-53836-K247EX |
Automatic cable reeler – Stainless Steel c/w Stainless steel junction box
Designed to be fixed to the top of a floating roof tank to enable a connection between the site wiring and the floating roof. The cable reeler feeds cable in and out as the floating roof moves up and down. This allows control over the cable and electrical connection without the risk of entanglement.
ATEX approved to II 1/3G Ex ia IIC T6
Ambient operating temperature -40 to 60 Deg C |
| 1-B6782-189 |
Ex Junction box c/w two cable glands
For use with all Alarmline Analogue and Digital sensor cables when installed in hazardous areas. EX e IP66 junction box suitable for zone 1, 2, 21 and 22. 2 x IP66 EX d brass cable glands. Contains 6 x 2.5mm terminals and 1 x 4mm earth terminal.
Commonly used on the top of floating roof tanks.
Dimensions (mm): 120w x 120h x 73.5d |
| 1-B6782-190 |
Ex Junction box c/w three cable glands
For use with all Alarmline Analogue and Digital sensor cables when installed in hazardous areas. EX e IP66 junction box suitable for zone 1, 2, 21 and 22. 2 x IP66 EX d brass cable glands. Contains 4 x 2.5mm terminals and 1 x 4mm earth terminal.
Commonly used on the roof of floating roof tanks.
Dimensions (mm): 120w x 120h x 73.5d |
| ACA-JBW |
Junction Box, IP65/66 w/ Cable Glands & Terminals
Polycarbonate suitable for terminating and jointing of Alarmline II sensor cables
Contains 5 x terminal connectors, 2 x M16 cable glands
Dimensions (mm): 94 x 94 x 57 |
| 1-K82024 |
In-Line jointing kit
A selection of heat shrinkable sleeving to be used when joining two sections of Alarmline sensor cable together. The sleeving is placed over the soldered joints of the two connected cables to protect and insulate the joints from damage. In-Line, jointing kits are supplied in packs of 10. |
|
Alarmline Analogue and Digital Sensor Cable Fixings |
| ACA-CE02-025 |
“Edge” clip, (Spring Steel) 2-3mm (1/16″) – Pack of 25
Spring steel clip used for fixing Alarmline II sensor cables to girders, angle bars, purlings etc.
Simple installation, clip is hammered on the mounting edge with no drilling or screwing required
Distance from mounting edge to sensor cable approx. 15mm, this distance can be extended by adding the ACA-BI20-XXX Bracket “I”
Suitable for edges with a web thickness of 2-3mm
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-CE02-100 |
“Edge” clip, (Spring Steel) 2-3mm (1/16″) – Pack of 100
Spring steel clip used for fixing Alarmline II sensor cables to girders, angle bars, purlings etc.
Simple installation, clip is hammered on the mounting edge with no drilling or screwing required
Distance from mounting edge to sensor cable approx. 15mm, this distance can be extended by adding the ACA-BI20-XXX Bracket “I”
Suitable for edges with a web thickness of 2-3mm
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-CE03-025 |
“Edge” clip, (Spring Steel) 3-8mm (2/16″) – Pack of 25
Spring steel clip used for fixing Alarmline II sensor cables to girders, angle bars, purlings etc.
Simple installation, clip is hammered on the mounting edge with no drilling or screwing required
Distance from mounting edge to sensor cable approx. 15mm, this distance can be extended by adding the ACA-BI20-XXX Bracket “I”
Suitable for edges with a web thickness of 3-8mm
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-CE03-100 |
“Edge” clip, (Spring Steel) 3-8mm (2/16″) – Pack of 100
Spring steel clip used for fixing Alarmline II sensor cables to girders, angle bars, purlings etc.
Simple installation, clip is hammered on the mounting edge with no drilling or screwing required
Distance from mounting edge to sensor cable approx. 15mm, this distance can be extended by adding the ACA-BI20-XXX Bracket “I”
Suitable for edges with a web thickness of 3-8mm
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-CE08-025 |
“Edge” clip, (Spring Steel) 8-14mm (5/16″) – Pack of 25
Spring steel clip used for fixing Alarmline II sensor cables to girders, angle bars, purlings etc.
Simple installation, clip is hammered on the mounting edge with no drilling or screwing required
Distance from mounting edge to sensor cable approx. 15mm, this distance can be extended by adding the ACA-BI20-XXX Bracket “I”
Suitable for edges with a web thickness of 8-14mm
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-CE08-100 |
“Edge” clip, (Spring Steel) 8-14mm (5/16″) – Pack of 100
Spring steel clip used for fixing Alarmline II sensor cables to girders, angle bars, purlings etc.
Simple installation, clip is hammered on the mounting edge with no drilling or screwing required
Distance from mounting edge to sensor cable approx. 15mm, this distance can be extended by adding the ACA-BI20-XXX Bracket “I”
Suitable for edges with a web thickness of 8-14mm
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-CE14-025 |
“Edge” clip, (Spring Steel) 14-20mm (9/16″) – Pack of 25
Spring steel clip used for fixing Alarmline II sensor cables to girders, angle bars, purlings etc.
Simple installation, clip is hammered on the mounting edge with no drilling or screwing required
Distance from mounting edge to sensor cable approx. 15mm, this distance can be extended by adding the ACA-BI20-XXX Bracket “I”
Suitable for edges with a web thickness of 14-20mm
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-CE14-100 |
“Edge” clip, (Spring Steel) 14-20mm (9/16″) – Pack of 100
Spring steel clip used for fixing Alarmline II sensor cables to girders, angle bars, purlings etc.
Simple installation, clip is hammered on the mounting edge with no drilling or screwing required
Distance from mounting edge to sensor cable approx. 15mm, this distance can be extended by adding the ACA-BI20-XXX Bracket “I”
Suitable for edges with a web thickness of 14-20mm
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-CT-025 |
‘T’ Clip – pack of 25
Suitable for all Alarmline sensor cables excluding the Stainless Steel braided. Used to install sensor cables on to flat surfaces that are suitable for drilling i.e. wood and concrete.
Distance from mounting surface to sensor cable: 25mm
Material: Low density Polyethylene resin
Peak melting temperature 120°C
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-CT-100 |
‘T’ clip – pack of 100
Suitable for all Alarmline sensor cables excluding the Stainless Steel braided. Used to install sensor cables on to flat surfaces that are suitable for drilling i.e. wood and concrete.
Distance from mounting surface to sensor cable: 25mm
Material: Low density Polyethylene resin
Peak melting temperature 120°C
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-CP-025 |
“P” Clip c/w Silicon Sleeve – Pack of 25
Suitable for mounting all types of Alarmline II sensor cables. The “P” clip can also be use to secure the Alarmline sensor cable to other metallic cable clips.
Dimensions (mm): 12w x 16h x 27d |
| ACA-CP-100 |
“P” Clip c/w Silicon Sleeve – Pack of 100
Suitable for mounting all types of Alarmline II sensor cables. The “P” clip can also be use to secure the Alarmline sensor cable to other metallic cable clips.
Dimensions (mm): 12w x 16h x 27d |
| ACA-CPSS-025 |
“P” Clip Stainless steel c/w Silicon Sleeve – Pack of 25
Suitable for mounting all types of Alarmline II sensor cables. The “P” clip can also be use to secure the Alarmline sensor cable to other metallic cable clips.
Material: Stainless steel
Dimensions (mm): 12w x 16h x 27d |
| ACA-CPSS-100 |
“P” Clip Stainless steel c/w Silicon Sleeve – Pack of 100
Suitable for mounting all types of Alarmline II sensor cables. The “P” clip can also be use to secure the Alarmline sensor cable to other metallic cable clips.
Material: Stainless steel
Dimensions (mm): 12w x 16h x 27d |
| ACA-B706-025 |
“7” Bracket (Pipe Clip), 60mm (2.4″) (Zintec) c/w Silicon Sleeve – Pack of 25
Suitable fixing clip for hanging Alarmline II sensor cables below pipes. Simple installation requires no drilling, clip is secured to the pipe using a suitable cable tie.
Material: Zintec (steel coated with Zinc plating)
Dimensions (mm): 20w x 60h x 50d
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-B706-100 |
“7” Bracket (Pipe Clip), 60mm (2.4″) (Zintec) c/w Silicon Sleeve – Pack of 100
Suitable fixing clip for hanging Alarmline II sensor cables below pipes. Simple installation requires no drilling, clip is secured to the pipe using a suitable cable tie.
Material: Zintec (steel coated with Zinc plating)
Dimensions (mm): 20w x 60h x 50d
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-B706SS-025 |
Pipe clip – Stainless steel c/w Silicon sleeve – Pack of 25
Suitable fixing clip for hanging Alarmline II sensor cables below pipes. Simple installation requires no drilling, clip is secured to the pipe using a suitable cable tie.
Material: Stainless steel
Dimensions (mm): 20w x 60h x 50d
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-B706SS-100 |
Pipe clip – Stainless steel c/w Silicon sleeve – Pack of 100
Suitable fixing clip for hanging Alarmline II sensor cables below pipes. Simple installation requires no drilling, clip is secured to the pipe using a suitable cable tie.
Material: Stainless steel
Dimensions (mm): 20w x 60h x 50d
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BVSS-025 |
“V” Bracket, (Stainless Steel) c/w Silicon Sleeve – Pack of 25
specifically designed to fit Admiralty standard cable tray. Allows sensor to be fixed to the underside of the cable tray.
Material: Stainless Steel
Requires suitablecable tie (ACA-TW series), these are ordered separately.
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BVSS-100 |
“V” Bracket, (Stainless Steel) c/w Silicon Sleeve – Pack of 100
specifically designed to fit Admiralty standard cable tray. Allows sensor to be fixed to the underside of the cable tray.
Material: Stainless Steel
Requires suitablecable tie (ACA-TW series), these are ordered separately.
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BU06-025 |
“U” Bracket, 60mm (2.4″) (Zintec) c/w Silicon Sleeve – Pack of 25
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Zintec (steel coated with Zinc plating)
Dimensions (mm): 20w x 60h x 50d
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BU06-100 |
“U” Bracket, 60mm (2.4″) (Zintec) c/w Silicon Sleeve – Pack of 100
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Zintec (steel coated with Zinc plating)
Dimensions (mm): 20w x 60h x 50d
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BU06SS-025 |
“U” Bracket, 60mm (2.4″) Stainless steel c/w Silicon Sleeve – Pack of 25
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Stainless steel
Dimensions (mm): 20w x 60h x 50d
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BU06SS-100 |
“U” Bracket, 60mm (2.4″) Stainless steel c/w Silicon Sleeve – Pack of 100
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Stainless steel
Dimensions (mm): 20w x 60h x 50d
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BL05-025 |
“L” Bracket, 50mm (2″) (Zintec) c/w Silicon Sleeve – Pack of 25
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Zintec (steel coated with Zinc plating)
Dimensions (mm): 20w x 50h
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BL05-100 |
“L” Bracket, 50mm (2″) (Zintec) c/w Silicon Sleeve – Pack of 100
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Zintec (steel coated with Zinc plating)
Dimensions (mm): 20w x 50h
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BL05SS-025 |
“L” Bracket, 50mm (2″) Stainless Steel c/w Silicon Sleeve – Pack of 25
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Stainless steel
Dimensions (mm): 20w x 50h
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BL05SS-100 |
“L” Bracket, 50mm (2″) Stainless Steel c/w Silicon Sleeve – Pack of 100
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Stainless steel
Dimensions (mm): 20w x 50h
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BL10-025 |
“L” Bracket, 100mm (3.9″) (Zintec) c/w Silicon Sleeve – Pack of 25
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Zintec (steel coated with Zinc plating)
Dimensions (mm): 20w x 100h
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BL10-100 |
“L” Bracket, 100mm (3.9″) (Zintec) c/w Silicon Sleeve – Pack of 100
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Zintec (steel coated with Zinc plating)
Dimensions (mm): 20w x 100h
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BL10SS-025 |
“L” Bracket, 100mm (3.9″) Stainless Steel c/w Silicon Sleeve – Pack of 25
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Stainless Steel
Dimensions (mm): 20w x 100h
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BL10SS-100 |
“L” Bracket, 100mm (3.9″) Stainless Steel c/w Silicon Sleeve – Pack of 100
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Stainless Steel
Dimensions (mm): 20w x 100h
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BL20-025 |
“L” Bracket, 200mm (7.9″) (Zintec) c/w Silicon Sleeve – Pack of 25
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Zintec (steel coated with Zinc plating)
Dimensions (mm): 20w x 200h
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BL20-100 |
“L” Bracket, 200mm (7.9″) (Zintec) c/w Silicon Sleeve – Pack of 100
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Zintec (steel coated with Zinc plating)
Dimensions (mm): 20w x 200h
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BL20SS-025 |
“L” Bracket, 200mm (7.9″) Stainless Steel c/w Silicon Sleeve – Pack of 25
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Stainless Steel
Dimensions (mm): 20w x 200h
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BL20SS-100 |
“L” Bracket, 200mm (7.9″) Stainless Steel c/w Silicon Sleeve – Pack of 100
Suitable for mounting Alarmline II sensor cables to any flat surface which can be drilled or screwed into.
Material: Stainless Steel
Dimensions (mm): 20w x 200h
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BI20-025 |
Bracket “I”, 200mm (7.9″) (Zintec) c/w Silicon sleeve – Pack of 25
The “I” bracket can be bolted on to our range of Zintec or Stainless steel clips to extend the distance of the sensor cable from the mounting surface.
Length: 200mm, Material: Zintec (steel coated with Zinc plating)
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BI20-100 |
Bracket “I”, 200mm (7.9″) (Zintec) c/w Silicon sleeve – Pack of 100
The “I” bracket can be bolted on to our range of Zintec or Stainless steel clips to extend the distance of the sensor cable from the mounting surface.
Length: 200mm, Material: Zintec (steel coated with Zinc plating)
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BI20SS-025 |
Bracket “I”, 200mm (7.9″) Stainless Steel c/w Silicon sleeve – Pack of 25
The “I” bracket can be bolted on to our range of Zintec or Stainless steel clips to extend the distance of the sensor cable from the mounting surface.
Length: 200mm, Material: Stainless steel
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-BI20SS-100 |
Bracket “I”, 200mm (7.9″) Stainless Steel c/w Silicon sleeve – Pack of 100
The “I” bracket can be bolted on to our range of Zintec or Stainless steel clips to extend the distance of the sensor cable from the mounting surface.
Length: 200mm, Material: Stainless steel
Note: Suitable cable tie will be required for securing sensor cable to clips, see available cable tie options ACA-TW series. |
| ACA-RS-025 |
Silicon sleeve – Pack of 25
Square patch of silicon which is designed for use with metallic fixing clips. The Silicon sleeve is designed to wrap around the Alarmline II sensor cable before securing it to the fixing clip, the silicon sleeve prevents the sensor cable from damage and also insulates it from the clip
Dimensions (mm): 25 x 25 x 1mm thickness |
| ACA-RS-100 |
Silicon sleeve – Pack of 100
Square patch of silicon which is designed for use with metallic fixing clips. The Silicon sleeve is designed to wrap around the Alarmline II sensor cable before securing it to the fixing clip, the silicon sleeve prevents the sensor cable from damage and also insulates it from the clip
Dimensions (mm): 25 x 25 x 1mm thickness |
| ACA-TW11W-025 |
Tie Wrap (PA66) 110°C (230°F) – Pack of 25
UV stabilised tie wrap for securing Alarmine II sensor cable to fixing clips
Material: Polyamide 66
Operating temperature: 110 Deg C (230 Deg F)
Suitable for indoor or outdoor installation
Length: 100mm
Colour: Black
must be used with silicon sleeve check clip specification, if silicon sleeve is not included with the clip it will need to be ordered seperately ACA-RS-XXX |
| ACA-TW11W-100 |
Tie Wrap (PA66) 110°C (230°F) – Pack of 100
UV stabilised tie wrap for securing Alarmine II sensor cable to fixing clips
Material: Polyamide 66
Operating temperature: 110 Deg C (230 Deg F)
Suitable for indoor or outdoor installation
Length: 100mm
Colour: Black
must be used with silicon sleeve check clip specification, if silicon sleeve is not included with the clip it will need to be ordered seperately ACA-RS-XXX |
| ACA-TW17-025 |
Tie Wrap (PA66) 170°C (338°F) – Pack of 25
High corrossion resistane and strength tie wrap for securing Alarmine II sensor cable to fixing clips
Material: ETFE
Suitable for indoor or outdoor installation
Operating temperature: 170 Deg C (338 Deg F)
Length: 100mm
Colour: Blue
must be used with silicon sleeve check clip specification, if silicon sleeve is not included with the clip it will need to be ordered seperately ACA-RS-XXX |
| ACA-TW17-100 |
Tie Wrap (PA66) 170°C (338°F) – Pack of 100
High corrossion resistane and strength tie wrap for securing Alarmine II sensor cable to fixing clips
Material: ETFE
Suitable for indoor or outdoor installation
Operating temperature: 170 Deg C (338 Deg F)
Length: 100mm
Colour: Blue
must be used with silicon sleeve check clip specification, if silicon sleeve is not included with the clip it will need to be ordered seperately ACA-RS-XXX |
| ACA-TWSS-025 |
Tie Wrap Stainless Steel – Pack of 25
Stainless steel tie wrap for securing Alarmine II sensor cable
Suitable for indoor or outdoor installation
Length: 125mm
must be used with silicon sleeve check clip specification, if silicon sleeve is not included with the clip it will need to be ordered seperately ACA-RS-XXX |
| ACA-TWSS-100 |
Tie Wrap Stainless Steel – Pack of 100
Stainless steel tie wrap for securing Alarmine II sensor cable
Suitable for indoor or outdoor installation
Length: 125mm
must be used with silicon sleeve check clip specification, if silicon sleeve is not included with the clip it will need to be ordered seperately ACA-RS-XXX |
| ACA-TWT |
Stainless Steel Tie Wrap Tool
Tool for the installation of stainless steel cable ties
The tool has an adjustable tensioner to ensure that cable ties are not overtightened potentially damaging the sensor cable |
